Super Power Electric provides residential wiring and rewiring services for homeowners across Red Bank, Monmouth County, and Central New Jersey. Whether you need a single circuit repaired, a full-home rewire for older wiring, new circuits for a renovation, or dedicated wiring for high-demand equipment, our licensed electricians handle it — permitted, inspected, and to current NJ code.
The wiring inside your walls is the one part of your electrical system you can’t see — and it’s often the part that needs the most attention. Homes in Monmouth County span more than a century of construction, and the wiring inside them ranges from knob-and-tube (pre-1930s) to cloth-insulated wire (1930s–1950s) to aluminum branch circuits (1965–1973) to modern copper Romex. Each type has different failure modes, different risks, and different solutions.
NJ Electrical License #12849. Family-owned since 1996. Over 900 five-star reviews.
The type of wiring in your home depends almost entirely on when it was built. Here’s what we typically find in Monmouth County’s housing stock and what each type means for your homes electrical safety
Our crews usually see this ancient wiring in victorian and early 20th-century homes in Red Bank, Fair Haven, Little Silver, Long Branch, and Asbury Park.
Knob-and-tube (K&T) consists of individual copper conductors run through porcelain knobs and tubes, with air space around the wires for cooling. When it was installed, it was state of the art. The problem today: K&T has no ground wire, the rubber insulation has become brittle and often crumbles when touched, and it was never designed for modern electrical loads. Worse, many older homes have had insulation blown into walls and attics that now surrounds the K&T wiring — eliminating the air gap it needs to dissipate heat safely.
K&T wiring is not automatically a code violation in NJ (existing wiring is grandfathered), but it cannot be extended, modified, or connected to new work. Most insurance companies in New Jersey either won't insure a home with active knob-and-tube or charge significantly higher premiums. If you're buying or selling a home with K&T, rewiring is almost always a condition of the sale or the insurance.
We commonly see this in mid-century homes throughout Monmouth County, particularly in Middletown, Eatontown, Shrewsbury, and older sections of Tinton Falls.
Cloth-insulated wiring uses rubber-coated conductors wrapped in a cloth fabric sheath. After 70–90 years, the rubber deteriorates and the cloth becomes brittle, exposing bare copper. This creates arc fault risk — bare conductors near wood framing or insulation can arc and ignite. Cloth wiring also lacks a ground wire in most installations.
Cloth wiring doesn't always require a full rewire. If the insulation is intact and the wiring is in good condition, it can continue to serve safely. But any circuit with deteriorated insulation, crumbling sheathing, or evidence of overheating needs to be replaced. We assess each circuit individually and recommend targeted replacement where needed rather than assuming a full rewire is the only option.
Aluminum wiring itself conducts electricity adequately. The problem is at the connections — where aluminum wire meets copper-rated outlets, switches, and breakers. Aluminum expands and contracts more than copper when it heats and cools, which loosens connections over time. Loose connections overheat. The U.S. Consumer Product Safety Commission found that homes with aluminum wiring at connections are significantly more likely to have fire-risk conditions at outlets and switches than homes with copper wiring.
Most homes built after 1973 and all new constructions have this modern standard.
This non-metallic sheathed cable (NM-B, commonly called Romex) with copper conductors is the current standard for residential wiring. It includes a ground wire, is rated for the loads modern homes require, and is compatible with all current code requirements including AFCI and GFCI protection. If your home has copper Romex in good condition, there's typically no need for rewiring — though individual circuits may need repair or your panel may need upgrading to support additional capacity. Panel upgrades →
For many homes, the most effective and cost-efficient fix is COPALUM or AlumiConn connectors — specially rated crimp or set-screw connectors that create a permanent, code-compliant copper-to-aluminum junction at every outlet, switch, and fixture. This addresses the connection problem without the cost and disruption of pulling all new wire. We assess every aluminum-wired home individually: if the wiring is in good condition and properly remediated at connections, a full rewire may not be necessary.
However, if the aluminum wiring shows signs of overheating (discolored wire, melted insulation, scorched outlet boxes), full circuit replacement with copper is the right call.
Wiring work requires NJ permits, inspection, and a licensed electrician. The consequences of improper wiring — arc faults, overheated connections, house fires — are severe and often invisible until something goes wrong. We handle every wiring project with permits pulled through your local municipality, work inspected by the local electrical inspector, and every connection made to current NEC and NJ code.
You’ll get upfront pricing on every project, whether it’s a single circuit repair or a full-home rewire. No hourly billing. No surprises.
Ready to wire your home? Fill out the form below and one of our technicians will contact you as soon as possible.
Call Us Directly: 732-851-8487!
We handle all types of residential wiring — from new construction rough-in to renovation wiring to individual circuit additions in existing homes. If your in need of new electrical wiring or a replacement, these are some of the common cases we find our techs are called for.
Complete rough-in and finish wiring for new homes, additions, and major renovations. We work with your builder and architect to plan circuit layouts, outlet placement, and panel sizing before walls go up. Includes all branch circuits, dedicated circuits for major appliances, structured wiring for data/networking, low-voltage pre-wire for security and audio, and panel installation. All work meets current NEC 2020 requirements.
Adding a home office, finishing a basement, converting a garage, or building an addition — each requires new wiring tied into your existing panel. We assess whether your current panel has capacity for the new circuits or whether a panel upgrade is needed, run new circuits to the new space, and install outlets, switches, and fixtures to current code. We also handle the permitting and inspection coordination with your local building department.
Certain appliances and equipment require their own dedicated circuit — a circuit that serves only that device with no other outlets or loads sharing it. We run dedicated circuits for:
If you're tripping breakers when you run specific equipment, you likely need a dedicated circuit. Circuit breaker services →
We’ve been wiring and rewiring homes across Central New Jersey since 1996 — from knob-and-tube replacement in 1920s Red Bank Victorians to aluminum wiring remediation in 1970s Holmdel colonials to full new-construction wiring for new builds in Tinton Falls. Over 900 five-star reviews from homeowners throughout Monmouth County.
Aluminum branch circuit wiring — installed in an estimated 2 million U.S. homes between 1965 and 1973 — presents a documented fire risk at connection points. The CPSC has found that homes with aluminum wiring are significantly more likely to have fire-risk conditions at outlets and switches, primarily because aluminum expands and contracts more than copper, loosening connections over time.
Many home insurance providers in New Jersey either decline to insure homes with unremediated aluminum wiring or require a licensed electrician’s certification that the connections have been properly addressed. If you’re buying a home with aluminum wiring, expect the home inspector to flag it — and expect the insurance company to require remediation before issuing a policy.
Aluminum wiring is one of the most common deal-breakers in Monmouth County home sales. Buyers’ inspectors flag it, lenders require it to be addressed, and sellers who don’t remediate it before listing lose negotiating leverage.
If your home has aluminum wiring, you have a few different options to make it safer and code compliant including:
A code-compliant alternative to COPALUM that uses a set-screw lug to connect copper pigtails to aluminum wire. Slightly less expensive to install, widely accepted by inspectors and insurers.
Removing all aluminum branch circuits and replacing with copper NM-B cable. This is the most complete solution but also the most expensive and most disruptive. Recommended when the aluminum wire itself shows signs of damage — discoloration, overheating, melted insulation, or when the home is undergoing a major renovation and walls are already open.
We assess every aluminum-wired home individually. A full rewire isn’t always necessary — and we won’t recommend one if remediation is the smarter choice for your situation.
Not every wiring issue requires a rewire. But certain signs indicate the wiring itself — not just an outlet or breaker — needs replacement:
K&T can't be buried in insulation, can't be connected to new work, and triggers insurance and real estate complications. If the K&T circuits are still active, replacement is the right path.
If the cloth sheathing is intact and the rubber insulation underneath isn't deteriorated, the wiring may be fine. But if the insulation crumbles when touched, exposes bare copper, or shows discoloration from overheating, those circuits need replacement.
Warm outlets, discolored outlet boxes, melted wire insulation at connection points, or a burning smell near outlets and switches — these indicate the connections are failing. If the wire itself is damaged, remediation alone won't solve it.
AFCI breakers detect arcing — and old wiring with deteriorated insulation can cause legitimate arc faults. If an AFCI breaker keeps tripping on the same circuit and the breaker itself has been verified as functional, the wiring on that circuit likely has insulation damage.
A 1950s home wired for 60-amp service with 14-gauge wire on most circuits wasn't designed for central air, EV chargers, home offices, and modern kitchen appliances. If you're consistently tripping breakers, running out of circuits, or relying on extension cords and power strips to reach outlets — you may need both new wiring and a panel upgrade.
